Ryobi HP24 El manual del propietario Pagina 1

Highland PrecisionHP18 & HP24 Slab Saw Owner’s Manual and Operating InstructionsCaution: Read all safety and operating instructions before using t

10CARRIAGE FEED ENGAGE/DISENGAGEMENTLever operated clutch system using silicon bronze shoe with block (adjustable set screws).INDEXING OR ROCK CUT WID

11 HP18 & HP24 SPECIFICATIONHighland Precision Slab Saws weigh between 550 (HP18) and 750 (HP24) pounds dry. Do not attemp

12 HP18 & HP24 OIL/COOLANTRoc Cut Roc Cut from Diamond Pacic is a new synthetic water soluble cutting additive with r

13STARTUPSaw LubricantThe saw tank reservoir should be filled with oil to a point 1/4" to 3/8" of the bottom of the blade. This ensures adeq

14Automatic Shutoff (HP18 & HP24)Once a rock specimen has been securely vised inside ofthe saw, the operator can adjust the automatic shut-offcont

15Never operate the saw with the hood up, or hold a sharpening stone to the blade by hand. Use of the vise is mandatory under all operation conditions

16Handle Crank Cross Feed Adjustable Rock Cut Index ControlTo use the crank cross feed index wheel, simply clamp andsecure the cutting material into t

17Adjusting countersink screwAdjusting allen head screwThis adjustment will help the clutch block shoe to snugly engage the stainless steel feed screw

18MAINTENANCE FOLLOWING USEThe following maintenance should be performed following each use.Blade-Shaft BearingsRemove sheet metal cover over blade sh

19GENERAL MAINTENANCEOil Sludge Removal from ReservoirUse plumber's pipe wrench to remove drain cap. Allow free liquid to drain to a pan. Use a s

2Thank you for selecting the Barranca Diamond Highland Precision Slab Saw. We are certain that you will be pleased with your purchase. Barranca Diamon

20Worm Shaft and Pinion Gear LubricationThe worm drive shaft and pinion gear lubrication box on the rear of the saw should be checked for adequate gre

21TROUBLESHOOTINGSaw Will Not StartCheck power cord and receptacle.Motor OverheatingIf motor overheats allow to cool for 2 to 3 hours, push reset butt

22 HP18 EXPLODED VIEWHP18 Highland Precision Slab Saw Part# 8302018

23 HP18 EXPLODED VIEWHP18 Highland Precision Slab Saw Part# 8302018

24 HP18 PARTS LISTHP18 Highland Precision Slab Saw Part# 8302018ITEM DESCRIPTION PART # QTY. 1 NUT, HEX, 3/8 - 16 1

25ITEM DESCRIPTION PART # QTY. 37 PULLEY, V 8" X 1" BORE 161800 138 SPRING, EXTENSION 162337 139 WHEEL., CASTER 2 X 1 - 1/4 162344 240 WHEEL

26HP18 Assembly, Vise Part # 166372 HP18 EXPLODED VIEW SCALE 0.375 3 8 10 11 13 14 15 17 18 19 20 21 22 23

27 HP18 PARTS LIST ITEM DESCRIPTION PART # QTY. 1 WASHER, FLAT, SAE, 5/16 151754 12 NUT, HEX, 1/4 - 20 151893 23 WA

28 HP24 EXPLODED VIEW HP24 Highland Precision Slab Saw Part# 8302024

29 HP24 EXPLODED VIEW HP24 Highland Precision Slab Saw Part# 8302024

3SAFETY PRECAUTIONS Read and follow all safety, operating and maintenance instructions. Failure to read and follow these instructions could result in

30 HP24 PARTS LIST ITEM DESCRIPTION PART # QTY. 1 NUT, HEX, 3/8 - 16 101188 172 NUT, HEX, 5/16 - 18 101196 83 PULL

31 HP24 PARTS LIST ITEM DESCRIPTION PART # QTY. 37 WHEEL, CASTER 3 X 1 - 1/4 162794 238 BELT, A57 163098 139 MANUA

32 HP24 EXPLODED VIEW 4 5 6 8 9 10 11 14 15 16 18 19 20 21 22 23 24 26 27 28 29 30 31 32 33 34

33 HP24 PARTS LIST HP24 Highland Precision Vise Assembly Part# 167368ITEM DESCRIPTION PART # QTY. 1 BOLT, HEX HD T

34 HP-18 & HP24 WARRANTYBarranca Diamond warrants to the original retail purchaser for a period of 90 days except as n

35 HP-18 & HP24 WARRANTYSPECIFICS APPLICABLE TO LIMITED WARRANTY OF DIAMOND BLADES AND CORE BITSLaser Welded Blade

36 HP-18 & HP24 SERVICE & WARRANTYREPLACEMENT PARTSReplacement parts for this tool may be ordered form your Barranca Diamond

37NOTES

38NOTES

39NOTES

4REDUCE THE RISK OF UNINTENTIONAL STARTSMake sure the ON/OFF switch is in the OFF position before plugging in a power tool.ROTATING OR MOVING PARTSKee

Barranca Diamond Products, Inc.1315 Storm ParkwayTorrance, CA 90501Toll-Free: (800) 421-5830Phone: (310) 539-5221Fax: (310) 539-5158www.barrancadiamo

5DIRECTION OF FEEDAlways feed work into a blade or cutter in the direction shown in this manual. All blades, grinding wheels or polishing belts should

6 HP18 & HP24 SAFETYSawing and drilling generate dust. Excessive airborne particles may cause irritation to eyes, s

7 HP18 & HP24 SAFETYWARNINGIn order to prevent electrical shock and injury, the following electrical safety precaut

8ELECTRICAL REQUIREMENTS AND GROUNDING INSTRUCTIONSTo avoid the possibility of the appliance plug or receptacle getting wet, position the saw to one s

9Model# HP18 HP18 HP24Motor Baldor Baldor BaldorHorsepower 1.5 Hp 1.5 Hp 1.5 HpVoltage 120V / 60 Hz 120V / 60 Hz 120V / 60 HzAmperage 8 8 8Motor RPM 1