Ryobi BTS10S Manual del operador descargar pdf (Pagina 6)

• Never perform any operation freehand, which means

usingonlyyourhands to supportorguidethe workpiece.

Always use either the rip fence or the miter guide to

positionand guide the work.

• Never stand or have any part of your body in line

with the path of the saw blade.

• Never reach behind, over, or withinthree inches of the

blade with either hand for any reason.

• Move the rip fence out of the way when cross-cutting.

• Never use the rip fence as a cut-off gauge whencross-

cutting.

• Never attempt to free a stalled saw blade without first

turning the saw off and disconnecting the saw from the

power source.

• Use a support for the sides and back of the saw table

when sawing wide or long workpieces. To prevent

tipping, use a sturdy "outrigger" support if a table

extension is more than 24 inches long and is attached to

the saw,

• Avoid kickbacks (workthrownback toward you) by:

Keeping the blade sharp.

Keeping rip fence parallelto the saw blade.

Keeping riving knife, anti-kickbackpawls, and blade

guard in place and operating.

Not releasing the work before it is pushedall the way

pastthe saw blade usinga push stick.

Notrippingworkthat is twistedor warped or does not

have a straightedge to guide alongthe fence.

• Avoid awkward operations and hand positions where

a sudden slip could cause your hand to move intothe

blade.

• Check with a qualified electrician if grounding

instructionsare notcompletelyunderstoodor if in doubt

as to whetherthe tool is properlygrounded.

• Use only correct electrical devices: 3-wire extension

cords that have 3-prong grounding plugs and 3-pole

receptaclesthat accept the toors plug.

• Do not modify the plug provided. If it will not fit the

outlet, have the proper outlet installed by a qualified

electrician.

• Use only recommended accessories listed in this

manual. Blades must be 10" (254 mm) in diameter, rated

for at least 4,800 rpm or higher, with 5/8" (16 mm) arbor

holes. Use of accessories that are not listed may cause

the risk of personal injury. Instructions for the safe use of

accessories are included with the accessory.

• Double check all setups. Make sure blade is tight and

not making contact with saw or workpiece before

connecting to power supply.

• Make sure the work area has ample lighting to see

the work and that no obstructions will interfere with safe

operation before performing any work using this tool,

• Always turn off saw before disconnecting it, to avoid

accidental starting when reconnecting to power supply.

Never leave the table saw unattended while connected

to a power source.

• Save these instructions. Refer to them frequently and

use to instruct other users. If you loan someone this tool,

loan them these instructions also.

Anti-Kickback Pawls

Device which, when properly installed and maintained, is

designed to stop the workpiece from being kicked back

toward the front of the saw duringa dppingoperation.

Arbor

The shaft on which a blade or cuttingtool is mounted.

Bevel Cut

A cuttingoperationmade with an angled blade.

Compound Miter Cut

A singlecutmade withbotha miterangle anda bevelangle.

Cross Cut

A cut or shaping operation made across the grain of the

workpiece.

Cut-off Stock

The unusedmaterial that remains after a cuffingoperation,

Dado

A non-through cut which produces a square sided notch or

trough in the workpiece.

Featherboard

A device used to help controlthe workpiece by guiding it

securely against the table or fence during any rip cut

operation.

Freehand

Performinga cut withoutusinga fence, mitergauge, fixture,

hold down clamp, or other proper device to keep the

workpiecafromtwisting duringthe cut.

Gullets

The valleysor notchesbetween the teeth in a saw blade.

Gum

A sticky, sap-based residue from wood products.

Page 6

1 2 3 4 5 6 7 8 9 10 11 ... 23 24

Comentarios a estos manuales

Sin comentarios

Ryobi BTS10S Manual del operador Pagina 6

Comentarios a estos manuales

Relacionado con productos y manuales para Herramientas Eléctricas Ryobi BTS10S