Ryobi WS7211 Manual del operador Pagina 9
- Pagina / 40
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
9 — English
INSTALLING THE SPLASH HOOD
See Figure 6 - 7, page 14.
Remove bevel table.
Install the L-shaped splash hood bracket into the lip
located under the table behind the wheel.
Install the washers and screws into table and through
splash hood bracket then tighten securely.
NOTE: Be sure that hood bracket is aligned with cutting
wheel so that it does not interfere with material being
cut.
Align splash hood with wheel and slide over bracket. Line
up through holes in splash hood with slot in splash hood
bracket.
NOTE: Always adjust splash hood horizontally to table
and slightly above tile thickness. Hood should not be
touching tile.
Install hex bolt through hood and bracket. Thread splash
hood knob onto bolt and tighten to desired height.
Replace bevel table.
INSTALLING THE RIP GUIDE
See Figure 8, page 15.
Turn knob on rip guide counterclockwise to loosen.
Slide rip guide onto side of table.
Use rip guide scale, located on front and rear of table, to
set rip guide to desired width of cut.
Turn rip guide knob clockwise to tighten securely.
ASSEMBLY
INSTALLING THE MITER GUIDE
See Figure 8, page 15.
Slide miter guide onto rip guide from front.
Adjust rip guide to desired position and secure.
Adjust to desired angle using angle scale and tighten
securely with miter guide knob.
INSTALLING THE OVERFLOW DRAIN
See Figure 9, page 15.
Remove bevel table.
Locate hole on bottom of water fill reservoir.
Push overflow drain into hole firmly.
Replace bevel table.
FILLING THE WATER RESERVOIR
See Figure 10, page 15.
Remove bevel table.
Fill water reservoir with clean tap water to fill line.
NOTE: Overflow drain prevents overfilling.
Replace bevel table.
To change reservoir water:
Unplug tile saw.
Remove overflow drain and empty into a bucket, do not
allow water to splash onto ground or around machine.
Discard waste water in accordance with local regulations.
OPERATION
WARNING:
Do not allow familiarity with tools to make you careless.
Remember that a careless fraction of a second is suf-
ficient to inflict serious injury.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes, resulting in possible
serious injury.
WARNING:
Do not use any attachments or accessories not recom-
mended by the manufacturer of this tool. The use of at-
tachments or accessories not recommended can result
in serious personal injury.
APPLICATIONS
You may use this tool for the purposes listed below:
Straight line cutting operations such as cross cutting,
mitering, ripping, and beveling
NOTE: This saw is designed to cut man-made tile, pavers,
natural stone products, and stone tile products only.
- OPERATOR’S MANUAL 1
- TABLE OF CONTENTS 2
- WARRANTY 2
- GENERAL SAFETY RULES 3
- SPECIFIC SAFETY RULES 4
- WARNING: 5
- CAUTION: 5
- ELECTRICAL 6
- FEATURES 7
- ASSEMBLY 8
- OPERATION 10
- MAINTENANCE 12
- TABLE DES MATIÈRES 13
- INTRODUCTION 13
- GARANTIE 13
- RÈGLES DE SÉCURITÉ GÉNÉRALES 14
- SYMBOLES 16
- CARACTÉRISTIQUES ÉLECTRIQUES 17
- CARACTÉRISTIQUES 18
- ASSEMBLAGE 19
- UTILISATION 20
- ENTRETIEN 23
- REGLAS DE SEGURIDAD GENERALES 25
- SÍMBOLOS 27
- PARTES ELÉCTRICAS 28
- CARACTERÍSTICAS 29
- 8 — Español 30
- FUNCIONAMIENTO 31
- MANTENIMIENTO 34
- Fig. 1 Fig. 2 35
- 7 in. TILE SAW 40
- SIERRA DE LOSAS 40
- DE 178 mm (7 pulg.) 40
Relacionado con productos y manuales para Herramientas Eléctricas Ryobi WS7211
Herramientas Eléctricas Ryobi RE601 Especificaciones
(24 paginas)
(24 paginas)
(24 paginas)Vivitar DVR 830XHD manuals
Owner’s manuals and user’s guides for Camcorders Vivitar DVR 830XHD.
We providing 1 pdf manuals Vivitar DVR 830XHD for download free by document types: Owner's Manual
Comentarios a estos manuales